Envoy NT9010A Guia do Utilizador

™WARNINGThis manual contains information on limitations regarding product use and function and information on the limitations as to liability of the m

6Section 2: Using Your NT9010 SystemOperating the System from the NT9010 controllerThe NT9010 controller provides easy to understand voice prompts to

Using Your NT9010 System7Remote Telephone AccessNOTE: Please pause for 1 second between key presses when entering access codes or commands on a remote

82. If the memo is not for you, you can press to stop the playback. If you press before the playback finishes, the Ready light will continue to fla

9Section 3: Turning Your System On (Arming) and Off (Disarming)This section describes how to turn your system on and off. Read this section care-fully

10Tur ning Off Your System1. If you are outside, enter through the entry/exit door. The keypad beeps to remind you to turn off the system.NOTE: Enteri

Turning Your System On (Arming) and Off (Disarming)11Tur ning On Your System When Everyone is Away (Away Mode)When you turn on your system using the A

12Tur ning On Your System While You Are At Home (Stay Mode)Use the Stay mode when you want to stay on the premises, and also want to pre-vent unauthor

Turning Your System On (Arming) and Off (Disarming)13NOTE: Pressing will only turn on the system. To turn the system off, you must enter a valid [ac

14Exiting When the System is On (Quick Exit)Your installer will tell you if the Quick Exit feature will work on your system. You can use the quick exi

15Section 4: Dealing With Alarms and EmergenciesRead this section carefully so that you will know what to do if your system goes into alarm.If you ret

iQuick Reference GuideThe following chart lists the basic functions of your system, and the keys to press for each function. Refer to the listed page

16Intrusion (Burglary) AlarmsA steady siren means an intrusion alarm. The system may also announce the label for the zone(s) that triggered the alarm,

Dealing With Alarms and Emergencies17Calling for HelpThe NT9010 has three pairs of emergency keys. Using these keys you can send an immediate Fire, Au

18Section 5: Using Advanced FunctionsThis section describes how to perform more specialized functions: turning off spe-cific detectors (bypassing zone

Using Advanced Functions19Checking Trouble ConditionsYour system continuously checks for a number of possible trouble conditions. If one of these trou

20Te s t i n g Yo u r SystemTest your system every week. Report any problems immediately to your installation company. NOTE: Perform system tests du

21Section 6: Customizing Your SystemThis section describes how to customize your system to suit your needs. Refer to this section for detailed instruc

22Tur ning the Door Chime On or OffIf your installer has enabled the door chime feature, your NT9010 will beep when-ever designated doors or windows a

23Section 7: Fire SafetyRead this section carefully. It contains important information about fire safety.Household Fire Safety AuditMost fires occur i

24• A good plan emphasizes a quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings or pets as this wastes valuab

25Section 8: Guidelines forLocating Smoke DetectorsResearch has shown that all hostile fires in homes gen-erate smoke to a greater or lesser extent. E

iiTable of ContentsQuick Reference Guide iTable of Contents iiLimited Warranty iiiAbout This Guide 1NT9010 controller Features 2Section 1: Introductio

26Section 9: Replacing BatteriesFrom time to time, the batteries in the detectors and other components on your system will need to be changed. If a de

Replacing Batteries27®Door/Window ContactsWLS925L-433To remove the cover of the universal trans-mitter, squeeze both sides of the unit where the notch

28Smoke DetectorsWLS906-433The WLS906-433 requires six Eveready Energizer AA batteries. To replace the batteries, remove the detector from the mountin

29GlossaryAccess code A 4- or 6-digit code you enter on the keypad to turn your system on or off, or to use other system features.Alarm When a zone is

30Entry/exit doorsYour installer will program the doors you usually use to enter or exit the premises as the entry/exit doors. These doors are program

31System InformationFill out the following information for future reference and store this guide in a safe place.For ServiceCentral Station Informatio

32Zone InformationThere are ________ active zones on the system.Zone Protected Area Zone Type Zone Protected Area Zone Type01 1702 1803 1904 2005 2106

33IndexAAC power trouble message 19Access codesadding 21changing 21defined 29erasing 21Master code 30programming 21telephone code 6Alarmchecking 16def

34WARNING Please Read CarefullyNote to InstallersThis warning contains vital information. As the only individual in contact with sys-tem users, it is

35FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by DigitalSecurity Controls Ltd. could void your authority to use t

iiiLimited WarrantyDigital Security Controls Ltd. warrants the original purchaser that for a period oftwelve months from the date of purchase, the pro

©2001 Digital Security Controls Ltd.Toronto • Canada • www.dsc.comPrinted in Canada 29005093 R007

1About This GuideThis NT9010 User’s Guide is designed for anyone using a NT9010 or NT9010A Security System. The NT9010 has many useful features. Read

2NT9010 Controller FeaturesThis is the NT9010 controller. It controls and monitors all devices on your NT9010 security system. You can access all syst

NT9010 Controller Features3➊ MicrophoneYou can use the microphone to record a voice memo on the NT9010. To record a memo, press the Record button, the

4StayExitChimeAwayStatusPlaybackRecordVolume369852147*0#ReadySystemArmed™Section 1: IntroductionYour installer has set up your system with your home o

Introduction5Fire Detection This NT9010 controller is capable of monitoring fire detection devices such as smoke detectors and providing a warning if